|
|
click on image for larger view
|
Don't Have Adobe Acrobat Reader? |
|
|
| 12 |
2104 |
P-CLIP (3/8", Plastic) - Use to fasten the foam-insulated part of a 2-wire cable to the Body |
| 14 |
2260 |
SCREWS (#6, 7/16", Phil Pan-Flat Head) - Use to fasten P-Clips, Sideplates, and Lanyard Pin |
| 15 |
1601 |
PLUG (3-Pin, Female, 2-Wire) - For front of Power Supply |
| 16 |
S7930 |
EZ-SWIVEL (For 2-wire Cable) - Can be used on any 2-wire Cable Assembly |
| 17 |
A16250 |
CABLE ASSEMBLY (2-Wire, 51 Ft., Floating) - AquaJet, Aquabot Turbo T-Jet |
| 25 |
S8730 |
JET VALVE ASSEMBLY (Black, Does not include Extension Brackets) - AquaJet |
| 25 |
A8730BL |
JET VALVE ASSEMBLY (Blue, Does not include Extension Brackets) - Aquabot Turbo T-Jet |
| 26 |
2002BLPR |
BODY ASSEMBLY (Blue, with Lock Tabs, no Valve Housing) - AquaJet |
| 26 |
A2005WTSL |
BODY ASSEMBLY (White, with Lock Tabs, no Valve Housing) - Aquabot Turbo T-Jet |
|
8351 |
FLAT PLUG (White, Plastic) - Use to plug large holes on the Body Assembly |
|
2400 |
NAIL PLUG (White, Plastic) - Use to plug small holes on the Body Assembly |
| 27 |
2251 |
SCREW (8-18 x 3/4, Phil Small Head) - Use to fasten the sides of the Jet Valve Assembly together |
| 29 |
S8731 |
VALVE SPRING (St.Steel, Hinge-spring, Use inside of Jet Valve Assembly) - AquaJet, Aquabot Turbo T-Jet |
| 32 |
8729 |
EXTENSION BRACKET (Black, 5 Holes, For Jet Valve) - AquaJet |
| 32 |
A8729BL |
EXTENSION BRACKET (Blue, 5 Holes, For Jet Valve) - Aquabot Turbo T-Jet |
| 33 |
8728 |
VALVE FLAP (White, Plastic, Use inside of Jet Valve Assembly with Valve Lock) - AquaJet, Aquabot Turbo T-Jet |
| 34 |
8727 |
VALVE LOCK (White, Plastic, Use inside of Jet Valve Assembly with Valve Flap) - AquaJet, Aquabot Turbo T-Jet |
| 35 |
8730 |
JET VALVE HOUSING (Black, Plastic, only housing, no Extension Brackets) - AquaJet |
| 36 |
SP9204BL |
LOCK-TABS (Blue, Plastic, to hold Bottom Lids to base of cleaners) - AquaJet, Aquabot Turbo T-Jet |
| 37 |
3394 |
BRACKET (For Center Wheel on Jet and Rover units) - Use to hold movable small black wheel |
| 38 |
2303 |
SCREWS (18-8, 8/32" x 1/2", Phil Bev Head) - Use to fasten the Lock-Tabs to the Body Assembly |
| 39 |
7133 |
LOCK-NUT (Nylon Insert, Hex) - Use to fasten the Screws of the Lock-Tabs |
| 40 |
1626 |
GROMMET (Rubber, Use around Cable Assembly on Body) - AquaJet, Aquabot Turbo T-Jet |
| 41 |
S3477 |
FOAM BLOCK (w/ Slot & Bracket, 4" Square Float) - AquaJet, Aquabot Turbo T-Jet |
|
3477 |
BRACKET (For Foam Block with Slot) - AquaJet, Aquabot Turbo T-Jet |
| 42 |
2660 |
BUSHING (Black, Plastic, Use around Poly-Tube on Body) - AquaJet, Aquabot Turbo T-Jet |
| 45 |
S3396Right |
SIDEPLATE (Black, Right side with Jet Nozzle) - AquaJet |
| 45 |
S3396Left |
SIDEPLATE (Black, Left side with Jet Nozzle) - AquaJet |
| 45 |
S3396BLRight |
SIDEPLATE (Blue, Right side with Jet Nozzle) - Aquabot Turbo T-Jet |
| 45 |
S3396BLLeft |
SIDEPLATE (Black, Left side with Jet Nozzle) - Aquabot Turbo T-Jet |
| 53 |
3393BK |
SMALL WHEEL (Black, For under Sideplate) - AquaJet, Aquabot Turbo T-Jet |
| 60 |
A600503 |
PUMP MOTOR (AquaJet, Aquabot Turbo T-Jet) |
| 61 |
4402 |
PROPELLER - AquaJet, Aquabot Turbo T-Jet |
| 62 |
2302 |
SCREWS (#8, 3/4", Phil Pan Head, Use to fasten the Pump to the Jet Valve) - AquaJet, Aquabot Turbo T-Jet |
| 63 |
6027 |
IMPELLER (Red) - AquaJet, Aquabot Turbo T-Jet |
| 64 |
6028 |
IMPELLER HOUSING (Red) - AquaJet, Aquabot Turbo T-Jet |
| 65 |
300096 |
TUBING (Clear PVC, 5/16"ID x 1/2"OD) - Use to divert water from the Impeller to the to the Jet Bracket |
| 85 |
4501 |
SCREW (8-18 x 1/2, Phil Pan Head) - Use to fasten the Extension Brackets to the Jet Valve Assembly |
| 86 |
SP5474 |
SHRINKABLE BUTT CONNECTORS (Light Blue, crimp closed and heat shrink to seal) |
| 87 |
SP1617 |
SHRINK TUBE (5/16", Blue) - For sealing 2-wire connections, use under Heat Shrink 1619 |
| 87 |
SP1619 |
SHRINK TUBE (1/2", Black) - For sealing 2-wire connections, use over Heat Shrink 1617 |
|
SP1611 |
SHRINK TUBE (3/4", Blue) - For sealing the Cable insulation below the P-Clip at the Handle Assembly |
| 89 |
2670C |
WHEEL COVER (Dome Disc, Snaps-in Hub) |
| 90 |
S2670 |
WHEEL ASSEMBLY (Black, Rubber, 6") - AquaJet, Aquabot Turbo T-Jet |
| 91 |
11067 |
STAR WASHER (For end of axle) - AquaJet, Aquabot Turbo T-Jet |
| 92 |
3603 |
WASHER (Nylon, Flat) - Use for AquaJet on the end of Wheel |
| 93 |
S101912 |
TUBE (Black, Plastic, 3" Oval, 12" Long) - AquaJet |
| 93 |
S1019BL12 |
TUBE (Blue, Plastic, 3" Oval, 12" Long) - Aquabot Turbo T-Jet |
| 94 |
S34201H |
AXLE (Fiberglass, 16.5"x1/2"OD, 1 hole, Front / Rear) - AquaJet, Aquabot Turbo T-Jet |
| 94 |
S8736 |
AXLE ASSEMBLY (White, Fiberglass, w/ Switching-Wedge) - AquaJet, Aquabot Turbo T-Jet |
| 95 |
11002 |
CLEVIS PIN (St.Steel, 1/4" x 2.232") - AquaJet, Aquabot Turbo T-Jet |
| 95 |
700016 |
CLEVIS PIN (St.Steel, 1/4" x 2.375") - AquaJet, Aquabot Turbo T-Jet |
| 96 |
2679 |
LANYARD (Black, Plastic, To tie onto Clevis Pin, attached to Tube or Body) - AquaJet, Aquabot Turbo T-Jet |
| 101 |
8100 |
FILTER BAG (Fine) - AquaJet, Aquabot Turbo T-Jet |
| 101 |
8200 |
FILTER BAG (Mesh) - AquaJet, Aquabot Turbo T-Jet |
| 103 |
5311 |
FILTER SCREEN (NEW, Blue, Bowl-shaped) All AquaJet, JetMAX, and Pool Rover units |
| 105 |
A9200XWB |
BOTTOM LID ASSEMBLY (White, W-shaped Wire Frame) - AquaJet, Aquabot Turbo T-Jet |
| 106 |
9305BL |
INTAKE VALVE FLAP (Blue Plastic) - AquaJet, Aquabot Turbo T-Jet |
| 108 |
S3103 |
H-FLOAT (Foam, Plastic, with Screws) - Fasten to Bottom Lid if cleaner's wall-climbing is not fast enough |
| 109 |
SP3104 |
SIDE POCKET FLOATS (White, Foam Blocks) - Put in Bottom Lid if wall-climbing is not fast enough |
| 110 |
7075C |
POWER SUPPLY (3-Prong Male, 90s Dial-Timer, 2hr Auto) - AquaJet |
| 111 |
7108 |
SOCKET ASSEMBLY (3-Pin, Male, 2-Wire) - AquaJet, Aquabot Turbo T-Jet |
| |
7115 |
SOCKET ASSEMBLY (Canadian CSA, 3-Pin, Female, 2-Wire) - Aquabot / Jet and Rover cleaners, AquaMAX / Junior |
| 112 |
7206 |
FUSE HOLDER (MINI, Phillips Head style) - AquaJet, Aquabot Turbo T-Jet |
|
7207 |
FUSE (2.5 Amp, MINI, 250 Volt, Slow- Blow) - AquaJet, Aquabot Turbo T-Jet |
| 114 |
7105 |
LIGHTED SWITCH (Thin, 1¼" x ½", Red with Light, 3-Wire) - Use for Power Supply |
| 114 |
7208 |
NON-LIGHTED SWITCH (Thin, 1¼" x ½", Red, 3-Wire) - Use for Power Supply with Dial or Digital Timer |
| 117 |
7041A |
HANDLE (Plastic, with Hardware) - Use on All Power Supplies except ULTRAMAX |
| 118 |
7102 |
CORD FOR POWER SUPPLY (3-Wire, Green, Black, and White) - For Power Supply |
| 119 |
7271D |
DIGITAL TIMER (NEW, Front Digital display, 1-7 hours Adjustable Auto-Off) - AquaJet, Aquabot Turbo T-Jet |
| 119 |
7132A |
TIMER 90 SECOND (OLD, Front Dial, 2hr Auto-Off, No Reset Switch) - For Power Supply of AquaJet |
| 119 |
7271 |
TIMER 90 SECOND (OLD, Front Dial, 2hr Auto-Off, 5 Wire, Reset Switch) - only when specified by Aqua Products |
|
|
|
|
800070 |
NOVUS 2 Plastic Polish 24 oz. Bottle |
|
1609 |
TIE (Blue, #4, Plastic, reusable) - Use for coiling the Cable Assembly among other things |
|
|
| |
|
|
|
|
|
|
|
