1	A10000WT	HANDLE ASSEMBLY (Bright White, Bracket included) - Aquabot Turbo T, Aquabot Turbo T-Solo Remote Control
2	S1100WT	HANDLE BRACKET (Bright White) - Aquabot Turbo T, Aquabot Turbo T-Solo Remote Control
8	1105	SCREW (10-32, 7/8", Phil Pan Head) - Use to fasten the Handle Bracket to the Body Assembly
9	2701	SCREW (#8, 11/16", Phil Pan Head) - Use to fasten Pump Motor
12	2109	P-CLIP (Blue, Coated Steel) - Use to fasten the Cable to the Handle of the Aquabot Turbo T / T-Solo / T2 / T4RC
13	2700	SCREWS (#8, 11/16", Phil Pan-Flat Head) - Use to fasten P-Clips, Sideplates, and Drive Motors
14	2260	SCREWS (#6, 7/16", Phil Pan-Flat Head) - Use for P-Clips, Outlet Top, and H-Float
15	1601	PLUG (3-Pin, Female, 2-Wire) - Aquabot Turbo T, Aquabot Turbo T-Solo Remote Control, Aquabot Turbo T2
16	S7930	EZ-SWIVEL (For 2-wire Cable) - Can be used on any 2-wire Cable Assembly
17	A16261T	CABLE ASSEMBLY (2-Wire, 60 Ft., Floating) - Aquabot Turbo T, Aquabot Turbo T-Solo Remote Control, Aquabot Turbo T2
	2250WT	OUTLET RING (Bright White, Ring only, does not include Top dome)
25	2230WT1	OUTLET TOP (Bright White, Top dome only, does not include bottom Ring)
26	A2005BL1	BODY ASSEMBLY (Blue, with Lock Tabs, Pin, Outlet Ring, Inserts) - Aquabot Turbo T, Aquabot Turbo T-Solo RC, Aquabot Turbo T2
36	SP9204W	LOCK-TABS (White, Plastic) - For All Body Assemblies, used to hold Bottom Lids to base of cleaners
38	2303	SCREWS (18-8, 8/32" x 1/2", Phil Bev Head) - Use to fasten the Lock-Tabs to the Body Assembly
39	7133	LOCK-NUT (Nylon Insert, Hex) - Use to fasten the Screws of the Lock-Tabs
40	1628	GROMMET (Rubber) - Use around Cable Assembly on Body
45	3400WT	SIDEPLATE (Bright White, no holes)
51	2600	BUSHING (White, Plastic, Use on each end of the Wheel Tubes and Pulley Assembly)
52	2610	BUSHING (White, Plastic, Use for Pin on Body Assembly)
55	3700	LARGE ROLLER (White, Plastic) - Supports the Drive Track, installs on Body Assembly Pin Support
56	3506	STEPPED SLEEVE ROLLER (White, Thicker end supports Drive Belts, Install on upper Sideplate legs)
57	SP3302	DRIVE BELTS (Tan)
58	A3605	PULLEY ASSEMBLY (2.75" long)
	3607	WASHER (Use on Pulley Assembly, Rounded edges facing inward)
	3397WT	NOZZLE BRACKET (White, Supports Drive Track, holds Nozzle in place)
	3398WT	NOZZLE (White, Snaps into Nozzle Bracket, connects to Poly Tubing for power washing under cleaner)
60	A600503	PUMP MOTOR (Inludes Propeller, Impeller and Impeller Housing)
61	4402	PROPELLER (Black, Plastic, D-shaped insert)
63	6027	IMPELLER (Red)
64	6028	IMPELLER HOUSING (Red)
65	300096	TUBING (Clear PVC, 5/16"ID x 1/2"OD) - Use to divert water from the Impeller to the Nozzle Bracket
80	A8545	DRIVE MOTOR (Blue, bare wire leads) - Aquabot Turbo T, Aquabot Turbo T-Solo RC
	3101	FLOAT (Place under Drive Motor)
86	SP5474	SHRINKABLE BUTT CONNECTORS (Light Blue, crimp closed and heat shrink to seal)
87	SP1617	SHRINK TUBE (5/16", Blue) - For sealing 2-wire connections, use under Heat Shrink 1619
87	SP1619	SHRINK TUBE (1/2", Black) - For sealing 2-wire connections, use over Heat Shrink 1617
88	1625	SHRINK TUBE (3/4", Black) - For sealing all medium sized connections at the Junction Box
90	A38205MG	WHEEL TUBE ASSEMBLY (White, Plastic, uses 11058 Retaining Rings)
91	11058	RETAINING RING (E-Clip, Use on each end of the Wheel Tubes)
92	3603	WASHER (Nylon, Flat, Use on each end of the Wheel Tubes)
97	SP3016BL	SUPER EZ-BRUSHES (Blue, Short) - Aquabot Turbo T, Aquabot Turbo T-Solo RC
99	3203	DRIVE TRACK with TRACTION TABS (Blue)
101	8100	FILTER BAG (Fine, for small debris)
101	8200	FILTER BAG (Mesh, for large debris)

103	SP5310	FILTER SCREEN (NEW, Blue, Folding Cage with Attachment Strings)
103	A5080	FILTER SCREEN (Blue, Rounded cage)
105	A9200XWB	BOTTOM LID ASSEMBLY (Blue, W-shaped Wire Frame)
106	9305BL	INTAKE VALVE FLAP (Blue Plastic, Use inside of Bottom Lid intakes)
108	S3103	H-FLOAT (Foam, Plastic, with Screws) - Fasten to Bottom Lid if cleaner's wall-climbing is not high enough
110	7098D	POWER SUPPLY (3-Prong, Male Socket, 7hr External Digital Timer) - Aquabot Turbo T
111	7108	SOCKET ASSEMBLY (3-Pin, Male, 2-Wire) - Aquabot Turbo T, Aquabot Turbo T-Solo RC
112	7206	FUSE HOLDER (MINI, Phillips Head style) - Aquabot Turbo T, Aquabot Turbo T-Solo RC
	7207	FUSE (2.5 Amp, MINI, 250 Volt, Slow- Blow) - Aquabot Turbo T, Aquabot Turbo T-Solo RC
114	7105	LIGHTED SWITCH (Thin, 1¼" x ½", Red with Light, 3-Wire) - Use for Power Supply
114	7208	NON-LIGHTED SWITCH (Optional, Thin, 1¼" x ½", Red, 3-Wire) - Use for Power Supply
117	7041A	HANDLE (Plastic, with Hardware)
118	7102	CORD FOR POWER SUPPLY (3-Wire, Green, Black, and White)
119	7074D	DIGITAL TIMER (Front Digital display, 1-7 hours Adjustable) - Aquabot Turbo T, Aquabot Turbo T-Solo RC
	800070	NOVUS 2 Plastic Polish 24 oz. Bottle - Polish for the plastic components
	1609	TIE (Blue, #4, Plastic, reusable) - Use for coiling the Cable Assembly among other things